Page 1 of 2
Cleanflight:)
Posted: Mon Mar 23, 2015 12:17 pm
by Graham Lawrie
I have just flashed Cleanflight on to my Full Naze32. All seems well, apart from my beeper is going constantly??
On Baseflight i just ticked a box, so when i flipped a switch it came on and off. I have tried playing with the slider on the beeper, but i cant get it to switch off??
Any suggestions??
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 12:52 pm
by Tony
is it set for the battery voltage, maybe those thresholds are incorrect.. just a guess...
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 12:59 pm
by Graham Lawrie
Really dont know enough about Cleanflight Tony:( Everything appears to work, just the beeper is on constantly, it changes the way it beeps when i switch it to what i class as rate mode. Remember the DX6i has only two position switches in Aux 1.
I must say though i like the look of Cleanflight:) Researching just now to see what i can find:)
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 1:16 pm
by Tony
unfortunately i dont have CF now, im sure on the first setup page there is an are for setting up the voltage detection with a tick box to enable it. try unticking that.... hopefully someone has the answer...
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 3:18 pm
by Graham Lawrie
Been a long search Tony watched 2 hours of youtube, a bit wiser, but still getting 3 beeps as if low voltage? Batteries are fine. Beeper works when i flick the switch. Set it up for low mode, when i flick the switch it goes to another mode which so far seems to be low battery, but they are ok. It will be something simple, but i dont know what:)
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 3:47 pm
by Tony
Have you setup the thresholds for the battery, it's works out what size lipo you have on from the voltage. Then determines the cell voltage. There is a window that sets up the low, mid and high voltages. Sounds like these are wrong. Wish I had my CF now.... Painless360(Lee) does a good vid on setting this up.... I'll have a look and send u the link
Try this mate
http://youtu.be/rrnxfn1mCXk
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 4:20 pm
by Graham Lawrie
I got it Tony:) I had a box ticked in Adjustments that i should not have:) Good learning curve with Cleanflight today.
Not brave enough for Autotune............yet:)
Loving Cleanflight:) its like the Rolls Royce version of Baseflight:)
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 4:20 pm
by Graham Lawrie
Tony wrote:Have you setup the thresholds for the battery, it's works out what size lipo you have on from the voltage. Then determines the cell voltage. There is a window that sets up the low, mid and high voltages. Sounds like these are wrong. Wish I had my CF now.... Painless360(Lee) does a good vid on setting this up.... I'll have a look and send u the link
Try this mate
http://youtu.be/rrnxfn1mCXk
Already watche the whole series of these:)
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 4:40 pm
by Tony
pleased you have it sorted Graham, yes CF is great, i dare not attempt putting it on this CC3D board i got off Dan in case i knack it. its flying great at the mo...lol
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 8:16 pm
by Stambo
Have you got the battery monitoring set up?
You have to have a wire from the flight pack direct to the naze.
I think it was next to the beeper pins.
You also have to have it level and recalibrate the accelerometers.
I tried autotune but was not happy with the results.
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 8:19 pm
by Graham Lawrie
Did not set up the battery monitoring Stambo, i prefer to use my TX timer:)
Re: Cleanflight:)
Posted: Mon Mar 23, 2015 10:01 pm
by Stambo
Graham Lawrie wrote:Did not set up the battery monitoring Stambo, i prefer to use my TX timer:)
Ahh, it's turned on by default so it thought the battery was low.
Re: Cleanflight:)
Posted: Sun Mar 29, 2015 8:06 pm
by wolfman76
I am just having trouble getting clean flight to connect to my naze32 afroflight acro board I have the drivers installed but not sure on the other two files I think I have them downloaded but not sure what to click in them to install
Re: Cleanflight:)
Posted: Sun Mar 29, 2015 9:42 pm
by Graham Lawrie
Kyle, have you got Cleanflight from Google Chrome? If so dont connect the board, click firmware flasher, choose your firmware board from the dropdown box, which should bev1.7.2NAZE 2015-2-18 0:27(STABLE) tick full chip erase, then connect board, click load firmware online, then flash firmware:)
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 1:07 am
by wolfman76
i think mine is loaded with the latest firmware already graham it came loaded just had to solder all the pins on
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 1:43 am
by Stambo
It will come with Baseflight, Cleanflight is superior as far as I am concerned and is well worth the minimal time it takes to install.
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 8:28 am
by Graham Lawrie
+1 on Stambo:) Cleanflight is better with more options:)
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 7:29 pm
by Lee
I'm having loads of problems.
Cant get rid of really bad roll wagging.
Doesn't seem to matter what P gain I put in, high or low, I just get fast wag on roll.
Other than that, it flies awesome.
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 8:12 pm
by Stambo
Lee wrote:I'm having loads of problems.
Cant get rid of really bad roll wagging.
Doesn't seem to matter what P gain I put in, high or low, I just get fast wag on roll.
Other than that, it flies awesome.
What FC you using Lee?
Re: Cleanflight:)
Posted: Tue Mar 31, 2015 8:23 pm
by KevG
Think Lee is on the Flip Stambo