Naze 32:)

Graham Lawrie · Post by **Graham Lawrie** » Sun Feb 14, 2016 1:33 pm

Right, finally got round to working on my Fossil and a bind issue.

The issue i had was that i could not get my satellite to bind. Voltage from the 3v pin on the Naze was ok but could barely get a flicker of light on the Lemon satellite.
I had the red heron of two satellites being faulty, which i can only think i fried them?

So today i connected again and went through everything from the start:
1. Fresh model and TX set up.
2. Flash Naze to the latest version.
3. Set "spektrum_sat_bind=9".
4. Power up..........YES!!

BIND COMPLETE:)

Next issue:
Roll and Throttle are working together??

I have tried several combinations but cant get the reciever section to work correctly.

I am taking it with me tomorrow as i journey North to work, and will work on it this week:)

Suggestions as always appreciated:)

KevG · Post by **KevG** » Sun Feb 14, 2016 4:12 pm

In the receiver tab have you set it to taer1234 (JR Spektrum)

Graham Lawrie · Post by **Graham Lawrie** » Sun Feb 14, 2016 5:18 pm

KevG wrote:In the receiver tab have you set it to taer1234 (JR Spektrum)

Yes Kev.
Not come across this before. My gut feeling is it is a Naze problem, thats why i reflashed with latest version. There are even channels moving via the sticks for Aux 1,2,3?
If i was not 100% i would say the wiring on channel servo leads were plugged into the wrong channels but they are not???

Stambo · Post by **Stambo** » Sun Feb 14, 2016 6:16 pm

Are you using pwm, ppm or serial?
Have you selected the correct one in the Naze?

You don't have some sort of mixing in the Tx?

Graham Lawrie · Post by **Graham Lawrie** » Sun Feb 14, 2016 6:59 pm

Serial with satellite, no rx new model in tx no mixing

Stambo · Post by **Stambo** » Mon Feb 15, 2016 3:15 am

How about a capture of your config screen in the configurator.

Graham Lawrie · Post by **Graham Lawrie** » Mon Feb 15, 2016 8:43 pm

Stambo wrote:How about a capture of your config screen in the configurator.

Iam 100 miles from home at work and guess what i left hanging in a bag in the hall:( DOH!!

Graham Lawrie · Post by **Graham Lawrie** » Sat Feb 20, 2016 5:08 am

Ok:) sorted the RX issue it was wrong setting in Spektrum 2048:)

Now the next problem, motors wont spin up and BLheli does not recognise the esc,s. This is the second time this has happened. Last time i had to reflash BLheli individually on Afro esc,s. Not sure if it is my laptop or something else?

Stambo · Post by **Stambo** » Sat Feb 20, 2016 6:09 am

What are the board LEDs doing?

Graham Lawrie · Post by **Graham Lawrie** » Sat Feb 20, 2016 6:49 am

Stambo wrote:What are the board LEDs doing?

This is really weird:( Cleanflight wont allow manually starting motors, BLheli doesn't recognize escs, but i armed it with TX and it spooled up??

I have 5 quads and never come across these issues before??

Graham Lawrie · Post by **Graham Lawrie** » Sat Feb 20, 2016 9:06 am

Well very confused?? Can get all functions working on Cleanflight, but cant get BLheli to work. Put Fossil together and did a test hover in the living room and it flew well??

Just the Volt and my 450 to get going and the Hanger is full again:)

RC-Hangout

Naze 32:)

Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)

Re: Naze 32:)