Cleanflight:)

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 12:17 pm

I have just flashed Cleanflight on to my Full Naze32. All seems well, apart from my beeper is going constantly??

On Baseflight i just ticked a box, so when i flipped a switch it came on and off. I have tried playing with the slider on the beeper, but i cant get it to switch off??

Any suggestions??

Tony · Post by **Tony** » Mon Mar 23, 2015 12:52 pm

is it set for the battery voltage, maybe those thresholds are incorrect.. just a guess...

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 12:59 pm

Really dont know enough about Cleanflight Tony:( Everything appears to work, just the beeper is on constantly, it changes the way it beeps when i switch it to what i class as rate mode. Remember the DX6i has only two position switches in Aux 1.

I must say though i like the look of Cleanflight:) Researching just now to see what i can find:)

Tony · Post by **Tony** » Mon Mar 23, 2015 1:16 pm

unfortunately i dont have CF now, im sure on the first setup page there is an are for setting up the voltage detection with a tick box to enable it. try unticking that.... hopefully someone has the answer...

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 3:18 pm

Been a long search Tony watched 2 hours of youtube, a bit wiser, but still getting 3 beeps as if low voltage? Batteries are fine. Beeper works when i flick the switch. Set it up for low mode, when i flick the switch it goes to another mode which so far seems to be low battery, but they are ok. It will be something simple, but i dont know what:)

Tony · Post by **Tony** » Mon Mar 23, 2015 3:47 pm

Have you setup the thresholds for the battery, it's works out what size lipo you have on from the voltage. Then determines the cell voltage. There is a window that sets up the low, mid and high voltages. Sounds like these are wrong. Wish I had my CF now.... Painless360(Lee) does a good vid on setting this up.... I'll have a look and send u the link

Try this mate

http://youtu.be/rrnxfn1mCXk

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 4:20 pm

I got it Tony:) I had a box ticked in Adjustments that i should not have:) Good learning curve with Cleanflight today.

Not brave enough for Autotune............yet:)

Loving Cleanflight:) its like the Rolls Royce version of Baseflight:)

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 4:20 pm

Tony wrote:Have you setup the thresholds for the battery, it's works out what size lipo you have on from the voltage. Then determines the cell voltage. There is a window that sets up the low, mid and high voltages. Sounds like these are wrong. Wish I had my CF now.... Painless360(Lee) does a good vid on setting this up.... I'll have a look and send u the link

Try this mate

http://youtu.be/rrnxfn1mCXk

Already watche the whole series of these:)

Tony · Post by **Tony** » Mon Mar 23, 2015 4:40 pm

pleased you have it sorted Graham, yes CF is great, i dare not attempt putting it on this CC3D board i got off Dan in case i knack it. its flying great at the mo...lol

Stambo · Post by **Stambo** » Mon Mar 23, 2015 8:16 pm

Have you got the battery monitoring set up?
You have to have a wire from the flight pack direct to the naze.
I think it was next to the beeper pins.
You also have to have it level and recalibrate the accelerometers.
I tried autotune but was not happy with the results.

Graham Lawrie · Post by **Graham Lawrie** » Mon Mar 23, 2015 8:19 pm

Did not set up the battery monitoring Stambo, i prefer to use my TX timer:)

Stambo · Post by **Stambo** » Mon Mar 23, 2015 10:01 pm

Graham Lawrie wrote:Did not set up the battery monitoring Stambo, i prefer to use my TX timer:)

Ahh, it's turned on by default so it thought the battery was low.

wolfman76 · Post by **wolfman76** » Sun Mar 29, 2015 8:06 pm

I am just having trouble getting clean flight to connect to my naze32 afroflight acro board I have the drivers installed but not sure on the other two files I think I have them downloaded but not sure what to click in them to install

Graham Lawrie · Post by **Graham Lawrie** » Sun Mar 29, 2015 9:42 pm

Kyle, have you got Cleanflight from Google Chrome? If so dont connect the board, click firmware flasher, choose your firmware board from the dropdown box, which should bev1.7.2NAZE 2015-2-18 0:27(STABLE) tick full chip erase, then connect board, click load firmware online, then flash firmware:)

wolfman76 · Post by **wolfman76** » Tue Mar 31, 2015 1:07 am

i think mine is loaded with the latest firmware already graham it came loaded just had to solder all the pins on

Stambo · Post by **Stambo** » Tue Mar 31, 2015 1:43 am

It will come with Baseflight, Cleanflight is superior as far as I am concerned and is well worth the minimal time it takes to install.

Graham Lawrie · Post by **Graham Lawrie** » Tue Mar 31, 2015 8:28 am

+1 on Stambo:) Cleanflight is better with more options:)

Lee · Post by **Lee** » Tue Mar 31, 2015 7:29 pm

I'm having loads of problems.
Cant get rid of really bad roll wagging.
Doesn't seem to matter what P gain I put in, high or low, I just get fast wag on roll.
Other than that, it flies awesome.

Stambo · Post by **Stambo** » Tue Mar 31, 2015 8:12 pm

Lee wrote:I'm having loads of problems.
Cant get rid of really bad roll wagging.
Doesn't seem to matter what P gain I put in, high or low, I just get fast wag on roll.
Other than that, it flies awesome.

What FC you using Lee?

KevG · Post by **KevG** » Tue Mar 31, 2015 8:23 pm

Think Lee is on the Flip Stambo

RC-Hangout

Cleanflight:)

Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)

Re: Cleanflight:)