Whats This?:)

Graham Lawrie · Post by **Graham Lawrie** » Sat Aug 01, 2015 5:27 am

Good luck with the new bus:) pics please:)
http://eu.banggood.com/Wholesale-Wareho ... 73352.html

Tony · Post by **Tony** » Sat Aug 01, 2015 6:47 am

Thanks G, I'll do a new thread of the truck when we pick it up at 10 today...

That board looks good mate, uses proper switching regulator, more efficient. Less heat dissipation... Looks like a good choice, just don't exceed its current rating of 2 amp... That's good for most stuff on a quad...

Graham Lawrie · Post by **Graham Lawrie** » Sat Aug 01, 2015 7:19 am

Thanks Tony:)

Lee · Post by **Lee** » Sat Aug 01, 2015 4:39 pm

I just tried the second one I have.
It's the same as the first.
12vwhen nothing is on, but drops to 4v as soon as a load is on it.

I'll be going back to my first ever diy pdb at this rate.

: 100_2388.JPG (179.21 KiB) Viewed 1843 times

: PDB.JPG (203.18 KiB) Viewed 1843 times

Tony · Post by **Tony** » Sun Aug 02, 2015 7:37 am

It's probably the track work Lee, too thin and too narrow to carry any current....

Graham Lawrie · Post by **Graham Lawrie** » Sun Aug 02, 2015 8:45 am

I will solder a test one when I get home tomorrow

@Lee is that liquid electrical clear tape on the board? I have black

Lee · Post by **Lee** » Sun Aug 02, 2015 8:54 am

That was just hot glue

I took a piece of copper tubing. Cut out a section and flattened it.
Cut into triangles and glued it to a piece of plywood, then put it on a sanding disc to make the copper a little thinner

Real Heath Robinson like LOL

Graham Lawrie · Post by **Graham Lawrie** » Sun Aug 02, 2015 9:33 am

Along as it does the job and works:) looks good to me:)

cml001 · Post by **cml001** » Sun Aug 02, 2015 10:59 am

Doesn't seem worth the effort to me... Great job Lee.. But just seems to me that simply soldering the wires would be easier.

Post by **danhampson** » Sun Aug 02, 2015 1:14 pm

here you go tony. this system will be run @ 3s and 4s

i cant embled the images from the site so here's the link to the PDB http://miniquadfpv.com/product/thug-pdb/

and links for the regulators themselfs
5v http://skpang.co.uk/catalog/pololu-5v-1 ... -1413.html
12v http://www.hobbytronics.co.uk/s10v2f12-12v-regulator

Tony · Post by **Tony** » Mon Aug 03, 2015 9:04 pm

What you using the 12 volt one for Dan, it's only rated at 0.2 amp, not a lot, and only up to 18 volts input... It won't tolerate any spikes at all either... It's cheap and nasty mate, sorry...

The 5 volt one is only 1 amp...

RC-Hangout

Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)

Re: Whats This?:)